A common start makes the landing place meaningful — quick review
Imagine several people giving you directions with arrows.
Coordinates (x, y) give the horizontal position first and vertical position second; (0, 0) records zero in both directions.
Standard position means vertex at (0, 0) and initial side on the positive x-axis. The Roman numerals I, II, III, IV mean 1, 2, 3, 4 and name the regions upper right, upper left, lower left, lower right, in counterclockwise order. A quadrantal angle ends on an axis.
Check that the vertex is at the origin and the initial side points right. Otherwise the angle is not in standard position.
Draw the landmarks: right 0°, up 90°, left 180°, down 270°, right again 360°.
Locate the terminal ray between two landmarks and name the quadrant, starting I in the upper right.
If the terminal ray is exactly on an axis, call the angle quadrantal and name the axis instead of a quadrant.
For several turns, remove complete revolutions before comparing to the landmarks.
In the table picture, read a column under Positive x-axis, right, then compare the matching information below it. Each column preserves one complete row of the reference table.
You are locating each finishing ray in a region or on an axis. In standard position, where do the terminal sides of 140° and 270° lie?
140°: Quadrant II.
270°: negative y-axis, a quadrantal angle.
Saying an angle of 90° is in Quadrant I. The upper-right region ends before its boundary. Exactly 90° is on the positive y-axis.
Check the vertex at the origin and the initial ray on the positive x-axis.
Use a coterminal measurement in 0° ≤ θ < 360° when the turn has extra or negative laps.
Mark the right, up, left, and down landmarks at 0°, 90°, 180°, and 270°.
If the terminal ray matches a landmark, name its axis and call it quadrantal.
Otherwise compare its measure with neighboring landmarks and name the region between them.
Line
A straight path that continues forever in both directions. Two points on it can name it.
Point
An exact location. A point has no width or length.
Ray
A straight path that begins at one endpoint and continues forever in one direction.
Angle
Two rays sharing an endpoint. You can also view an angle as the turn that moves one ray toward the other.
Vertex
The endpoint shared by an angle's two rays. It is the middle letter in a three-letter angle name.
Initial side
The ray where an angle's rotation begins.
Terminal side
The ray where an angle's rotation ends.
Clockwise
Turning in the direction a clock's hands normally move.
Counterclockwise
Turning in the direction opposite to a clock's usual hand movement.
Negative angle
An angle whose recorded rotation goes clockwise. Its sign describes direction, not whether its terminal side points left or right.
Full revolution
One complete turn that brings a rotating ray back to its starting position. Its size is 360° or 2π radians.
Degree (°)
An angle unit equal to one of 360 equal parts of a full revolution.
Standard position
An angle placement with vertex at the origin and initial side along the positive x-axis.
Rectangular coordinate system
A map of locations using a horizontal x-axis and a vertical y-axis that meet at a right angle.
Origin
The point (0, 0), where the x-axis and y-axis meet.
x-axis
The horizontal coordinate line. Points on it have y = 0.
y-axis
The vertical coordinate line. Points on it have x = 0.
Positive x-axis
The part of the horizontal axis pointing right from the origin.
Quadrant
One of the four open regions between the coordinate axes. The axes themselves belong to no quadrant.
Quadrantal angle
An angle in standard position whose terminal side lies on a coordinate axis.
Right angle
An angle of 90°, which is one quarter of a full revolution.
Straight angle
An angle of 180°, whose two sides point in opposite directions along one straight line.
Center
The point inside a circle equally distant from every point on the circle.
Integer
A whole-number count, positive or negative, or zero. It has no fractional part.
Coordinate axis
One of the two crossing number lines used to locate points: the x-axis or y-axis.