Radians count radius-lengths of curved distance — quick review
Imagine laying a flexible measuring tape around a round table.
For a nonnegative central opening, θ = radians, where s is the chosen arc length and r > 0 is the radius; signed turns use the direction rule.
180° = π radians; a full revolution is 360° = 2π radians.
Locate the center and the two radii forming the central angle. Follow the curved arc between their endpoints, because s measures the edge rather than a straight shortcut.
Express s and r in the same length unit, because their ratio must compare equal kinds of length.
Divide arc length by radius: θ = . The result counts radius-lengths, so it is in radians.
Write a degree sign for degrees. For radians, write the word when clarification helps; the instructor's notation usually omits a unit symbol.
Rebuild familiar angles from the half-turn fact 180° = π. The table is a reference you can reconstruct, not a separate set of facts to memorize.
In the table picture, the column under 30° gives because six 30° pieces make 180°. Read the other columns the same way and rebuild each from 180° = π.
You are finding the arc-to-radius count before and after doubling all lengths. An arc is 7.5 cm long on a circle of radius 5 cm. Find its central angle in radians. Then enlarge the circle and arc to twice their size.
Original circle: 1.5 radians.
Enlarged circle: 1.5 radians.
Reading 30 and 30° as the same angle. In the instructor's angle notation, a number without a degree sign is in radians. Write ° whenever the measurement is in degrees, and say radians when a bare number could be unclear.
Find the circle's center and identify the central angle's two sides.
Choose the arc described by the question and read its curved length s.
Put arc length and radius in the same length unit.
Compute θ = to count radius-lengths; label the result radians when helpful.
If the whole picture is enlarged, check that arc and radius enlarge by the same factor so their ratio stays unchanged.
Line
A straight path that continues forever in both directions. Two points on it can name it.
Angle
Two rays sharing an endpoint. You can also view an angle as the turn that moves one ray toward the other.
Vertex
The endpoint shared by an angle's two rays. It is the middle letter in a three-letter angle name.
Initial side
The ray where an angle's rotation begins.
Terminal side
The ray where an angle's rotation ends.
Clockwise
Turning in the direction a clock's hands normally move.
Counterclockwise
Turning in the direction opposite to a clock's usual hand movement.
Full revolution
One complete turn that brings a rotating ray back to its starting position. Its size is 360° or 2π radians.
Right angle
An angle of 90°, which is one quarter of a full revolution.
Straight angle
An angle of 180°, whose two sides point in opposite directions along one straight line.
Central angle
An angle whose vertex is at a circle's center.
Circle
All the points in a flat surface that are the same distance from one center point.
Center
The point inside a circle equally distant from every point on the circle.
Radius
A line segment from a circle's center to its rim, or the length of that segment.
Circumference
The distance all the way around a circle. Its formula is C = 2πr.
Arc
A curved piece of a circle's rim.
Radian
An angle unit: one radian is the central angle whose arc length equals the circle's radius.
Radian measure
An angle's size expressed in radians. For a positive central angle, divide arc length by radius: θ = .
Arc length (s)
The distance measured along an arc. For a positive central angle in radians, s = rθ.
θ (theta)
The Greek letter theta, commonly used to name an angle or its measure.
Degree measurement
Expressing the amount and direction of a turn using degrees.
Numerator
The top number or expression in a fraction. It counts pieces of the size named by the denominator.
Denominator
The bottom number or expression in a fraction. It tells the size of each counted piece. It cannot be zero.