Quarry School

Distance from a center and tolerance

Subject: MathematicsLeans on: Subtracting a negativeLeans on: Endpoint notationLeans on: Set-builder notation
Level 1 · FoundationsAbout 14 min read6 new terms
How this was estimated

Programmatic estimate. Rung levels, worked steps, prerequisites, terms and sentence length contribute to this level. It describes the lesson, not your ability.

Reading counts the whole lesson, including folded explanations, at 180 words a minute. Practice allows two minutes per item. These are planning assumptions; take the time you need.

AI estimate unavailable.

Path to here

Open the unit’s lesson list to follow the lesson order.

    Quick review (2 minutes)

    In plain words

    Now put your home at 5 instead of zero.

    Rule

    Distance between two real numbers A and B is |A − B| = |B − A|. Here A and B name the two positions. For an allowed distance r ≥ 0 from center c, at most r means |x − c| ≤ r, with ends c − r and c + r included. Strictly less than r means |x − c| < r, with the ends excluded. Exactly r means |x − c| = r. At least r means |x − c| ≥ r. More than r means |x − c| > r. The sign ± is read plus or minus: c ± r names the lower limit c − r and upper limit c + r. If r = 0, the two end positions coincide at c; an exact zero distance has only that one position.

    Step

    1. Choose a letter for the actual value, such as x, a resistance R, a score S, or a temperature T. Identify the center c.

    2. Find the permitted distance r. For a percent tolerance, multiply the size of the stated rating by the percent divided by 100.

    3. Read the words carefully. At most, no more than, and ends included use an equality bar under the comparison. Strictly less than and strictly more than leave the end out.

    4. Write |actual value − center|, then the comparison and distance.

    5. Locate the two positions c − r and c + r. Nearby means the stretch between them. Farther away means the left side or the right side beyond them. Exactly that distance means the two end positions.

    6. Keep the units. Use a closed, filled dot or a bracket for an included end; use an open, hollow dot or a parenthesis for an excluded end.

    Question

    A resistor has nominal resistance 680 ohms, ±5%. Express its allowable actual resistance R using absolute value and an interval.

    Answer

    |R − 680| ≤ 34
    646 ≤ R ≤ 714 ohms
    Interval: [646, 714] ohms

    Trap

    The center and permitted distance have different jobs. In |R − 680| ≤ 34, 680 names the rating, while 34 says how far the measurement may depart from it.

    Strategy

    1. Identify the actual value, center, and permitted distance.

    2. Write the absolute value of actual value minus center.

    3. Choose the sign using the exact words.

    4. Use the street endpoints center minus distance and center plus distance to describe allowed positions.

    Term

    absolute value

    Definition

    The absolute value of a number is its distance from zero. It keeps the size without the direction, so it is never negative.

    Term

    distance

    Definition

    Distance tells how far apart two places or numbers are. On a number line, the distance from A to B is |A − B|.

    Term

    output

    Definition

    An output is the value a function returns for an input. On its graph, the output is the vertical coordinate y = f(x).

    Term

    zero

    Definition

    A zero of a function is an input where its output is 0. On the graph, that input locates an x-intercept.

    Term

    interval

    Definition

    An interval is one connected stretch of the number line. It contains every number between its ends, with endpoints included or excluded as stated.

    Term

    set-builder notation

    Definition

    Set-builder notation names a set by a condition. In {x : condition} or {x | condition}, the separator means such that; here x is real.

    Term

    tolerance

    Definition

    Tolerance is the allowed size of a difference from a stated center. A percent tolerance is calculated from that center, then allowed above and below it.

    Term

    nominal value

    Definition

    The nominal value is the stated or labeled center for an item. Its actual measured value can differ within the allowed tolerance.

    Term

    absolute value bars

    Definition

    Absolute value bars are the pair of vertical marks around an expression. Compute the expression inside first, then take its distance from zero.

    Term

    endpoint

    Definition

    An endpoint is a numbered end of an interval. A closed (filled) dot or bracket includes it; an open (hollow) dot or parenthesis excludes it.

    Term

    actual value

    Definition

    The actual value is the measured amount for one item. It may differ from the nominal value because manufactured items are not perfectly identical.

    Term

    resistance

    Definition

    Resistance measures how strongly a part limits the flow of electricity. Its unit is the ohm; its actual measured value can differ from its stated nominal value.

    Term

    resistor

    Definition

    A resistor is a part that limits how much electricity flows. Its label gives a nominal resistance in ohms and may give an allowed tolerance.

    Term

    capacitor

    Definition

    A capacitor is a part that stores electric charge, an electrical amount, for later. Capacitance measures this stored charge per unit of voltage; manufactured capacitance values may vary within a tolerance.

    Term

    capacitance

    Definition

    Capacitance measures stored electric charge per unit of voltage. Electric charge is the stored electrical amount; voltage measures the electrical push. Manufacturing tolerance allows actual capacitance to differ from its nominal value.

    Term

    opposite

    Definition

    The opposite of a number is equally far from zero on the other side. The opposite of 0 is 0.

    Term

    set notation

    Definition

    Set notation names a collection. Curly braces with commas list its individual members.

    Term

    plus or minus

    Definition

    The symbol ± names both signs. In a tolerance, c ± r allows values from c − r through c + r.

    Term

    margin of error

    Definition

    A margin of error is the allowed size of a difference from a stated measurement or estimate.

    Term

    expression

    Definition

    An expression is a calculation made of numbers, letters, and operations. It does not by itself claim an equality.

    Term

    electric charge

    Definition

    Electric charge is an electrical amount that can be stored or moved. A capacitor can store charge for later.

    Term

    voltage

    Definition

    Voltage measures the electrical push between two places. Capacitance measures stored charge for each unit of that push.

    1 In plain words

    Now put your home at 5 instead of zero. To find how far you are from home, compare your position x with 5. The subtraction x − 5 says which side of home you are on and how far. Taking its absolute value keeps the distance. This makes |x − 5| the distance from the center 5. The same idea describes a manufactured part allowed to be a little too small or a little too large. That allowed difference is its tolerance. You name the center, measure the distance, and compare it with the permitted amount. This lets one statement cover departures in both directions.

    2 Picture it

    646714[646, 714]
    The allowable resistances form [646, 714], with both endpoint values included.

    Reminder

    Reminder: Subtracting a negative, Endpoint notation, Set-builder notation
    • Subtracting a negative. x − (−6) = x + 6. Keep parentheses around a negative center before simplifying.
    • Endpoint notation. A filled dot and bracket include an end. A hollow dot and parenthesis leave it out: [7, 11] includes 7 and 11; (7, 11) leaves both out.
    • Set-builder notation. {x | x ≥ 5} and {x : x ≥ 5} both mean all x such that x ≥ 5. A colon helps distinguish set notation from absolute value bars.

    3 Why

    Subtracting the center makes its own position count as zero difference: at x = 5, x − 5 = 0. At x = 8 the difference is 3; at x = 2 it is −3. Both positions are three units away. Reversing the subtraction reverses the direction, while the bars keep the distance. Thus |x − 5| = |5 − x|. To stay within an allowed distance r of a center c, you cannot go below c − r or above c + r. This follows by walking r units each way from c.

    4 The rule

    Distance between two real numbers A and B is |A−B|=|B−A|.

    Here A and B name the two positions. For an allowed distance r≥0 from center c, at most r means |x−c|≤r, with ends c−r and c+r included. Strictly less than r means |x−c|<r, with the ends excluded. Exactly r means |x−c|=r. At least r means |x−c|≥r. More than r means |x−c|>r. The sign ± is read plus or minus: c±r names the lower limit c−r and upper limit c+r. If r=0, the two end positions coincide at c; an exact zero distance has only that one position.

    The same idea, five ways

    Say it

    Say the distance between x and c. Read |x − c| as the absolute value of x minus c.

    Write it

    Subtract the center, then measure the size of the difference.

    In math
    • |x−c|=|c−x|
    • |x−c|≤r
    • c−r≤x≤c+r
    • [c−r,c+r]
    • {x:c−r≤x≤c+r}
    Like

    Move the home address before measuring how far away a house is.

    See it
    0246810+3lands on 8
    The center 5 and actual position 8 are three units apart.

    The same idea, other ways

    As a walk from the center

    Start at 5 and walk 3 right to 8. The difference 8 − 5 is 3, so |8 − 5| = 3. A walk 3 left reaches 2 and gives |2 − 5| = 3.

    0246810+3lands on 8
    A three-unit walk from 5 reaches 8.
    With opposite differences

    The output is the size of the difference. In the table, the columns under 2 and 8 both show 3 because these positions are equally far from 5.

    input xoutput |x − 5|235083
    Subtracting the center before taking absolute value measures distance from that center.
    As permitted error

    A part can be slightly smaller or larger than its intended size. A tolerance puts a limit on the distance between the measured size and the intended center.

    3.483.52[3.48, 3.52]
    The permitted bolt lengths run from 3.48 to 3.52 cm.
    WordsAbsolute value statement, r > 0Street picture
    Exactly r; at a distance of r|x−c|=rOnly c − r and c + r
    At most r; no more than r; within r, ends included|x−c|≤rBetween the ends, both included
    Less than r; strictly within r|x−c|<rBetween the ends, both left out
    At least r; no closer than r|x−c|≥rOutside either end, ends included
    More than r; farther than r|x−c|>rOutside either end, ends left out
    c ± r; margin of error r|x−c|≤rBetween c − r and c + r, ends included

    Part 1: Distance from a center

    Subtract the address of home before measuring how far away you are. Either order of subtraction gives the same distance.

    • Distance from c is |x − c|.
    • |x−c|=|c−x|.
    • |x| ≤ 4 means within or including four units of zero: −4 ≤ x ≤ 4, the interval [−4, 4].
    0246810−4lands on 1
    From 5 to 1 is a four-unit trip.

    Worked example

    Compare two subtraction orders

    Find the distance between 1 and 5.

    What it asks. Find the length of the trip between positions 1 and 5.

    Show the steps and the answer

    The plan. Subtract the positions and measure the size of that difference, then reverse the subtraction to check.

    0123456−4lands on 1
    The four-unit trip from 5 ends at 1.
    1. Plan. Subtract the positions and measure the size of that difference, then reverse the subtraction to check.
    2. Keep the subtraction inside intact.
    3. Distance has no negative sign.
    1. |1−5|=|−4|=4.Moving from 5 to 1 changes position by −4 but travels four units.
    2. |5−1|=|4|=4.Reversing the trip changes its direction but keeps its length.
    Answer
    The distance is 4.
    Double-check The four unit gaps are 1 to 2, 2 to 3, 3 to 4, and 4 to 5.

    Counterexamples

    What it is not, and the tempting wrong moves.

    ✗ Not this: The distance between 1 and 5 is −4.
    −4 is the difference in position for one direction of travel, not the length.
    ✓ Instead: |1−5|=|−4|=4.

    Tips and tricks

    • Either subtraction order gives the same distance once the bars are applied.

    Part 2: Absolute tolerance

    A tolerance stated in centimeters tells you directly how far a measured length may differ from the intended center. Think of a marked ruler with a short acceptable stretch on each side of 3.5 cm. Two hundredths can be added or subtracted because lengths have decimal parts too.

    • At most 0.02 from 3.5: |x − 3.5| ≤ 0.02.
    • The boundary values are included when the maximum error is allowed.
    3.483.52[3.48, 3.52]
    The filled ends include the acceptable limits 3.48 and 3.52 cm.

    Worked example

    A bolt within two hundredths

    A bolt must be within 0.02 cm of 3.5 cm, ends included. Write the condition and limits.

    What it asks. Find the acceptable bolt lengths, including their two limits.

    Show the steps and the answer

    The plan. Write distance from 3.5, then walk 0.02 cm below and above the center.

    3.483.52[3.48, 3.52]
    All lengths on the shaded stretch satisfy the tolerance.
    1. Plan. Write distance from 3.5, then walk 0.02 cm below and above the center.
    2. Within, ends included means at most.
    3. Write 3.5 as 3.50 when subtracting hundredths.
    1. |x−3.5|≤0.02.The bars measure the distance of the actual length from the intended 3.5 cm center; at most permits the maximum difference.
    2. 3.50−0.02=3.48 and 3.50+0.02=3.52.The two positions exactly two hundredths from 3.5 mark the acceptable ends.
    3. Write 3.48≤x≤3.52, or [3.48, 3.52].Every length between the ends is close enough, and both ends are allowed.
    Answer
    • |x−3.5|≤0.02
    • 3.48 ≤ x ≤ 3.52 cm
    • Interval: [3.48, 3.52] cm
    Double-check |3.48 − 3.5| = 0.02 and |3.52 − 3.5| = 0.02, so both ends sit exactly at the limit and are allowed.

    Counterexamples

    What it is not, and the tempting wrong moves.

    ✗ Not this: Only x ≤ 3.52 is required.
    That would allow lengths such as 3 cm, whose distance from 3.5 is 0.5 cm.
    ✓ Instead: Both limits are needed: 3.48 ≤ x ≤ 3.52.

    Tips and tricks

    • Keep the same measurement unit in the center, allowed distance, and answer.

    Part 3: Percent tolerance

    A percent tolerance makes the permitted difference depend on the stated rating. Five percent of a larger rating is a larger amount. A resistor is a part that limits how much electricity flows, and ohms measure its resistance. A capacitor stores electric charge, an electrical amount. Its capacitance is stored charge per unit of voltage, the electrical push. Only the measurements and units matter for this calculation.

    • Nominal value means the intended rating; actual value means the measured value.
    • Tolerance distance = size of rating × percent ÷ 100.
    • Resistance and capacitance are different measurements; use the units given.
    • A tolerance ±p% permits the same percentage below and above the rating. Common stated tolerances include ±1%, ±5%, and ±10%.

    Center: 680 ohms

    5%=5100

    Allowed distance: 34 ohms

    646 ≤ R ≤ 714

    Reminder

    Reminder: Percent
    • Percent. 2% = 2100 = 0.02. Multiply the center's size by this fraction.

    Worked example

    A two percent tolerance

    A 250-unit rating allows 2% variation. Find the limits.

    What it asks. Find the smallest and largest allowed values for a 250-unit rating.

    Show the steps and the answer

    The plan. Convert 2% of 250 to units, then subtract and add that amount.

    245255[245, 255]
    The rating's 2% tolerance permits [245, 255].
    1. Plan. Convert 2% of 250 to units, then subtract and add that amount.
    2. Percent is a fraction out of 100.
    3. Both ends are permitted.
    1. r=250×2100=500100=5 units.Multiplying the rating by two hundredths gives its permitted distance.
    2. Write |x−250|≤5.The measured value may differ from the rating by no more than 5 units.
    3. 250−5=245 and 250+5=255, so 245≤x≤255.Walking the allowed distance each way locates the included ends.
    Answer
    • Allowed difference: 5 units.
    • Allowed values: [245, 255].
    Double-check 5 ÷ 250 = 0.02 = 2%, so each endpoint uses exactly the permitted variation.

    Counterexamples

    What it is not, and the tempting wrong moves.

    ✗ Not this: A 2% tolerance always means two units.
    Two percent is a fraction of the rating, so its unit amount depends on that rating.
    ✓ Instead: For a 250-unit rating, 250 × 2100 = 5 units.

    Tips and tricks

    • Convert the percent to a measured distance before writing the bars.

    Part 4: Negative centers and plus or minus

    The home address can be negative. Subtract that entire address before measuring. Plus or minus, written ±, gives two directions from a center. For a tolerance it names a lower and an upper allowed limit. For a short list such as ±2, it names the numbers 2 and −2.

    • Distance from −2 is |x − (−2)| = |x + 2|.
    • 680 ± 34 gives limits 646 and 714.
    • ±2 means 2 and −2.
    • A margin of error is the largest stated distance allowed from a reported value.
    • A percentage point is a change of 1 in a percentage number: 52% to 53% changes by one percentage point. A margin stated in percentage points uses subtraction of these numbers, rather than a percent of the center.
    −6−4−202+3lands on 1
    Three units right from the negative center −2 reaches 1.

    Reminder

    Reminder: Subtracting a negative
    • Subtracting a negative. 1−(−2)=1+2=3.

    Worked example

    Within three of negative two

    Describe all numbers within 3 of −2, including the ends.

    What it asks. Find the permitted positions near a center left of zero.

    Show the steps and the answer

    The plan. Subtract the negative center correctly, then locate the two end positions by walking 3 each way.

    −51[−5, 1]
    The acceptable numbers lie between −5 and 1, including both ends.
    1. Plan. Subtract the negative center correctly, then locate the two end positions by walking 3 each way.
    2. x minus negative 2 becomes x + 2.
    3. The allowed ends are included.
    1. Write |x−(−2)|≤3, which is |x+2|≤3.The difference must be measured from center −2, and the distance can be at most 3.
    2. The left end is −2−3=−5. The right end is −2+3=1.These positions are exactly three units each way from the center.
    3. All positions between the ends work: −5≤x≤1, or [−5,1].They are no farther from −2 than the included two ends.
    Answer
    • |x + 2| ≤ 3
    • −5≤x≤1
    • Interval: [−5, 1]
    Double-check |−5 + 2| = |−3| = 3 and |1 + 2| = 3. At the center −2 the distance is zero, which is also allowed.

    Counterexamples

    What it is not, and the tempting wrong moves.

    ✗ Not this: Within 3 of −2 is written |x − 2| ≤ 3.
    That expression measures from positive 2.
    ✓ Instead: Write |x + 2| ≤ 3.

    Tips and tricks

    • Put a negative center in parentheses until the subtraction is simplified.

    5 How

    1. Choose a letter for the actual value, such as x, a resistance R, a score S, or a temperature T. Identify the center c.
    2. Find the permitted distance r. For a percent tolerance, multiply the size of the stated rating by the percent divided by 100.
    3. Read the words carefully. At most, no more than, and ends included use an equality bar under the comparison. Strictly less than and strictly more than leave the end out.
    4. Write |actual value − center|, then the comparison and distance.
    5. Locate the two positions c − r and c + r. Nearby means the stretch between them. Farther away means the left side or the right side beyond them. Exactly that distance means the two end positions.
    6. Keep the units. Use a closed, filled dot or a bracket for an included end; use an open, hollow dot or a parenthesis for an excluded end.

    Translate a distance statement

    1
    Is the distance given as a percent?
    YesMultiply the rating's size by percent ÷ 100 first.
    NoUse the stated distance and units.
    ↓
    2
    Does the wording say exactly or at a distance of?
    YesUse = and the two positions at that distance.
    NoCompare whether the value is nearer or farther.
    ↓
    3
    Does the wording say at most or strictly less?
    YesUse the stretch between the two end positions.
    NoAt least or more than permits positions beyond either end.
    ↓
    4
    Are the end positions allowed?
    YesUse an equals bar in the comparison and filled dots or brackets.
    NoUse a strict sign and hollow dots or parentheses.
    1. Identify the actual value, center, and permitted distance.
    2. Write the absolute value of actual value minus center.
    3. Choose the sign using the exact words.
    4. Use the street endpoints center minus distance and center plus distance to describe allowed positions.

    6 Worked example

    Worked example

    A resistor's permitted resistance

    OpenStax problem

    A resistor has nominal resistance 680 ohms, ±5%. Express its allowable actual resistance R using absolute value and an interval.

    What it asks. Find how far the measured resistance may depart from 680, and write all the allowed values.

    Show the steps and the answer

    The plan. Convert five percent to an allowed distance. Walk that distance below and above 680, including both ends.

    646714[646, 714]
    Filled ends include the permitted resistance limits 646 and 714 ohms.
    1. Plan. Convert five percent to an allowed distance. Walk that distance below and above 680, including both ends.
    2. Nominal value is the stated rating. Actual value is the measured number.
    3. ±5% permits the same percentage below and above the rating.
    1. Let R be the actual resistance in ohms. The center is 680 ohms.R names the measurement that varies, while 680 is the fixed rating.
    2. 5% =5100=0.05.Percent means out of one hundred.
    3. 680×5=3400; then 3400÷100=34 ohms.Five hundredths of 680 is the permitted distance from the rating.
    4. Write |R−680|≤34.The distance from the actual measurement to its rating can be at most 34 ohms.
    5. The lower end is 680−34=646. The upper end is 680+34=714.Walking 34 units either way from the center finds the two furthest allowed values.
    6. Write 646≤R≤714, or the interval [646, 714].Every value between these limits is close enough, and the equals bar includes both limits.
    Answer
    • |R−680|≤34
    • 646 ≤ R ≤ 714 ohms
    • Interval: [646, 714] ohms
    Double-check 646 is 34 below 680, and 714 is 34 above it. Both distances are 34. Also 34680 = 120 = 0.05 = 5%, so each endpoint uses the permitted percentage.

    Ladder: from easy to exam-hard

    Try each rung before you open its steps.

    Rung 1 of 6

    Exactly six from a negative center

    Describe all numbers exactly 6 from −1.

    What it asks. Find the two positions whose distance from −1 is exactly 6.

    Show the steps and the answer

    The plan. Write the distance statement, then walk six units each way from the center.

    −75
    Only the two marked positions are exactly six units from −1.
    1. Plan. Write the distance statement, then walk six units each way from the center.
    2. Subtracting −1 gives x + 1.
    3. Exactly uses an equals sign.
    1. Write |x−(−1)|=6, or |x+1|=6.The center is −1 and the required distance is 6.
    2. Walk left to −1−6=−7 and right to −1+6=5.On a straight line these are the two positions at that exact positive distance.
    Answer
    • |x + 1| = 6
    • x = −7 or x = 5
    • Set: {−7, 5}
    Double-check |−7 + 1| = |−6| = 6 and |5 + 1| = |6| = 6.

    Rung 2 of 6

    At most two from nine

    Describe all numbers at most 2 from 9.

    What it asks. Find the stretch of nearby positions, including the allowed limit.

    Show the steps and the answer

    The plan. Walk two units each way from 9 and keep the stretch between the ends.

    711[7, 11]
    Filled ends show that distance exactly two is allowed.
    1. Plan. Walk two units each way from 9 and keep the stretch between the ends.
    2. At most permits equality.
    3. Nearby positions lie between the two ends.
    1. Write |x−9|≤2.At most 2 means distance 2 or less from center 9.
    2. The two end positions are 9−2=7 and 9+2=11.They are the furthest permitted positions on the two sides.
    3. Keep 7≤x≤11, or [7, 11].Every position between them is no farther than 2, including the two ends.
    Answer
    • |x−9|≤2
    • 7 ≤ x ≤ 11
    • Interval: [7, 11]
    Double-check The center 9 has distance 0 and both ends have distance 2, so all meet the condition.

    Rung 3 of 6

    Strictly less than half a unit

    Describe all numbers less than 0.5 from 12.

    What it asks. Find nearby positions with the two maximum-distance ends excluded.

    Show the steps and the answer

    The plan. Locate 12 minus and plus 0.5, then keep positions strictly between them.

    11.512.5(11.5, 12.5)
    Hollow ends exclude distances exactly half a unit.
    1. Plan. Locate 12 minus and plus 0.5, then keep positions strictly between them.
    2. Less than leaves out equality.
    3. Half a unit is 0.5.
    1. Write |x−12|<0.5.The distance must be smaller than the stated half unit.
    2. The end positions are 12−0.5=11.5 and 12+0.5=12.5.These are exactly half a unit from the center.
    3. Keep 11.5 < x < 12.5, or (11.5, 12.5).The two ends have distance exactly 0.5 and must be left out, while every position between them is nearer.
    Answer
    • |x−12|<0.5
    • 11.5 < x < 12.5
    • Interval: (11.5, 12.5)
    Double-check 12 has distance zero and works; the ends each have distance 0.5 and fail a strict less-than comparison.

    Rung 4 of 6

    At least five from twelve

    Describe all numbers at least 5 from 12.

    What it asks. Find faraway positions in either direction, including distance exactly 5.

    Show the steps and the answer

    The plan. Locate the positions five each way from 12, then keep the outward sides.

    717(−∞, 7] ∪ [17, ∞)
    The two outward pieces include their boundary values.
    1. Plan. Locate the positions five each way from 12, then keep the outward sides.
    2. At least allows equality.
    3. Nearer positions in the middle fail.
    1. Write |x−12|≥5.The phrase at least requires distance 5 or greater.
    2. The two boundary positions are 12−5=7 and 12+5=17.These are exactly five units from the center.
    3. Keep x≤7 or x≥17.Positions to the left of 7 or to the right of 17 are far enough. Positions between them are too near.
    Answer
    • |x−12|≥5
    • x ≤ 7 or x ≥ 17
    • Interval: (−∞, 7] ∪ [17, ∞)
    Double-check 7 and 17 have distance 5 and work; the center 12 has distance 0 and fails.

    Rung 5 of 6

    A thermostat's strict departure

    A thermostat switches on when temperature T is more than 3 degrees from 70. Describe the switching temperatures.

    What it asks. Find when the temperature is too far below or above the center.

    Show the steps and the answer

    The plan. Write the strict distance comparison, find the boundary temperatures, and keep the outward regions.

    6773(−∞, 67) ∪ (73, ∞)
    The thermostat activates in either strict outside region.
    1. Plan. Write the strict distance comparison, find the boundary temperatures, and keep the outward regions.
    2. T is the actual temperature; 70 is the center.
    3. More than excludes a difference of exactly 3.
    1. Write |T−70|>3.The distance from temperature T to 70 must exceed 3.
    2. The two boundary temperatures are 70−3=67 and 70+3=73.They are exactly three degrees from the center.
    3. Keep T < 67 or T > 73.Those temperatures are farther away, while the two boundary temperatures are excluded by more than.
    Answer
    • |T−70|>3
    • T < 67 or T > 73
    • Interval: (−∞, 67) ∪ (73, ∞)
    Double-check 66 and 74 each differ by 4 and switch it on. 67 and 73 differ by exactly 3 and do not.

    Rung 6 of 6

    A poll's margin of error

    A poll reports 52% with a margin of error of 3 percentage points. Let p be the percentage number, such as 52. Describe the permitted values.

    What it asks. Find percentages within the stated departure from the reported center.

    Show the steps and the answer

    The plan. Treat p as a number on a percent scale and walk three percentage points each way from 52.

    4955[49, 55]
    The percentage-number interval includes its margin-of-error limits.
    1. Plan. Treat p as a number on a percent scale and walk three percentage points each way from 52.
    2. Here p = 52 means 52%, rather than the decimal 0.52.
    3. A margin of error includes its stated limits.
    1. Write |p−52|≤3.The distance from the reported percentage number is at most three percentage points.
    2. 52−3=49 and 52+3=55.These give the lower and upper percentage-number limits.
    3. Keep 49≤p≤55.Every percentage number between the ends is within the margin, including both ends.
    Answer
    • |p−52|≤3
    • 49 ≤ p ≤ 55
    • Interval for p: [49, 55]
    • Percentages: 49% through 55%
    Double-check 49 and 55 each differ from 52 by three percentage points. The center 52 differs by zero, so it also falls within the permitted margin.

    Counterexamples

    What it is not, and the tempting wrong moves.

    ✗ Not this: The distance from −6 is |x − 6|.
    That expression measures from positive 6. At x = −2 it gives 8, while −2 and −6 are only four units apart.
    ✓ Instead: Distance from −6 is |x − (−6)| = |x + 6|. At x = −2 this is |4| = 4.
    ✗ Not this: A 5% tolerance at 680 permits a difference of 680.
    680 is the center; the difference is five hundredths of it.
    ✓ Instead: 680 × 5100 = 34, so |R − 680| ≤ 34.

    Tips and tricks

    • Read |x − c| as the distance between x and c.
    • The textbook uses within with both interpretations. Its Try It answers include the ends, while its $200 discussion means strictly less. If wording is only within, state whether you include the ends; use a strict sign when it says less than or strictly.
    • A margin of error permits the same maximum departure on either side of the reported value.

    7 The trap

    The center and permitted distance have different jobs. In |R − 680| ≤ 34, 680 names the rating, while 34 says how far the measurement may depart from it.

    Problems marked OpenStax come from Precalculus 2e by Jay Abramson, published by OpenStax, under the CC BY-NC-SA 4.0 licence. Access for free at https://openstax.org/books/precalculus-2e/pages/1-introduction-to-functions.