Degrees, minutes and seconds: smaller pieces of a turn
Quick review (2 minutes)
Picture a shop that lets you exchange one large token for 60 smaller tokens, and each small token for 60 tiny ones.
1° = 60′ = 3600″ and 1′ = 60″. Decimal degrees = D + + . For subtraction: 90° = 89°59′60″ and 180° = 179°59′60″.
Here D, M, and S count degrees, minutes, and seconds, respectively.
For DMS subtraction, align the degree, minute and second columns. If needed, borrow one degree as 60 minutes, then one minute as 60 seconds.
Subtract each column after the units are available. Check by adding your answer to the original angle.
For DMS to decimal degrees, keep the degrees and add minutes ÷ 60 and seconds ÷ 3600.
For decimal degrees to DMS, keep the whole degrees. Multiply only the leftover decimal by 60; keep its whole minutes.
Multiply the new leftover decimal minute by 60 for seconds. Round at the end; if seconds round to 60, carry one minute. If minutes reach 60, carry one degree.
In the table picture, read a column under Degree, °, then compare the matching information below it. Each column preserves one complete row of the reference table.
A triangular plot of land has corners P, Q and R. A surveyor measures the angle at Q as ∠Q = 48°37′25″. A mapping program lists the angle at P in decimal degrees as ∠P = 63.4333°. (a) Write ∠P in degrees, minutes and seconds, rounded to the nearest second. (b) The three angles of a triangle add to 180°. Using your answer to (a), find ∠R in degrees, minutes and seconds. (c) Write ∠R in decimal degrees, rounded to four decimal places.
(a) ∠P ≈ 63°26′0″; (b) ∠R = 67°56′35″; (c) ∠R ≈ 67.9431°
Treating DMS as decimal digits. 6′ is ° = 0.1°, not 0.06°. Borrow and carry in groups of 60, not 100.
Read the requested operation and label the units in each column.
For DMS subtraction, exchange larger pieces until each smaller column has enough, then subtract matching columns.
For DMS to decimal degrees, use D + + before the final rounding.
For decimal degrees to DMS, keep the whole degrees, multiply the leftover by 60, keep the whole minutes, and multiply their leftover by 60.
Round seconds as requested and carry complete groups of sixty.
Check subtraction by addition, or check conversion by converting the unrounded value back.
Line
A straight path that continues forever in both directions. Two points on it can name it.
Point
An exact location. A point has no width or length.
Angle
Two rays sharing an endpoint. You can also view an angle as the turn that moves one ray toward the other.
Clockwise
Turning in the direction a clock's hands normally move.
Minute (′)
An angle unit equal to of a degree. It measures angle, not elapsed time.
Second (″)
An angle unit equal to of a minute or of a degree.
DMS notation
Writing an angle in degrees, minutes, and seconds, with symbols °, ′, and ″.
Decimal degrees
Writing an angle as a number of degrees with a decimal part instead of separate minutes and seconds.
Approximation
A value close to the exact amount, often obtained by rounding. The symbol ≈ means approximately equal.
Degree measurement
Expressing the amount and direction of a turn using degrees.
Numerator
The top number or expression in a fraction. It counts pieces of the size named by the denominator.
Denominator
The bottom number or expression in a fraction. It tells the size of each counted piece. It cannot be zero.
Common denominator
A shared bottom number used to rewrite fractions into matching-sized pieces before adding or subtracting them.
1 In plain words
Picture a shop that lets you exchange one large token for 60 smaller tokens, and each small token for 60 tiny ones. Angle measurements have the same exchange system. One degree contains 60 Minute (′) units, and one minute contains 60 Second (″) units. Here minutes and seconds are pieces of an angle, not elapsed time. DMS notation means degrees, minutes, seconds, like 25°43′37″. You can also write the same size as Decimal degrees, one number measured entirely in degrees. To subtract in DMS, exchange a larger piece when a smaller column has too little. To convert units, count how many smaller pieces make one larger piece.
Explain it like I am five
Think of a clock: an hour splits into 60 minutes, and a minute into 60 seconds. Angles split the same way. One degree (1°) is 60 minutes (60′), and one minute (1′) is 60 seconds (60″). Here minutes and seconds are slivers of an angle, not time. Writing 38°14′51″ is DMS notation (degrees, minutes, seconds): 38 degrees, 14 minutes, 51 seconds.
Example: find the complement of 38°14′51″, the angle that fills 90° with it. Write 90° as 90°0′0″. You cannot take 51″ from 0″, so trade. Trade 1° for 60′: 90°0′0″ = 89°60′0″. Trade 1′ for 60″: 89°60′0″ = 89°59′60″. The size did not change; only the pieces did.
Now subtract column by column. Seconds: 60″ − 51″ = 9″. Minutes: 59′ − 14′ = 45′. Degrees: 89° − 38° = 51°. The complement is 51°45′9″. Check by adding: 38°14′51″ + 51°45′9″ = 89°59′60″. Carry 60″ into 1′ to get 89°60′, then 60′ into 1° to get 90°.
2 Picture it
90°0′0″ = 89°60′0″
= 89°59′60″
= 64°16′23″
Reminder
Reminder: Fractions with matching units, Rounding, Subtraction check
- Fractions with matching units. ° = ° = 0.5° because dividing both fraction numbers by 30 keeps the same amount.
- Rounding. 18.6″ rounds to 19″ because it is 0.4″ from 19″ and 0.6″ from 18″.
- Subtraction check. After subtraction, add the removed amount back: 70° − 28° = 42°, and 42° + 28° = 70°.
3 Why
Because one degree contains 60 minutes and each of those contains 60 seconds, one degree contains 60 × 60 = 3600 seconds. Borrowing preserves the total measurement: exchange 1° for 60′, then exchange 1′ for 60″. Thus 90° = 89°60′0″ = 89°59′60″. Converting to decimals uses the same equivalence in reverse, since a minute is one sixtieth of a degree. Round only the final seconds or decimal answer so early rounding does not change later columns.
4 The rule
and .
Decimal degrees . For subtraction: and .Here D, M, and S count degrees, minutes, and seconds, respectively.
The same idea, five ways
Say degrees, angle minutes, angle seconds; the marks °, ′, and ″ identify the units.
DMS notation writes whole degrees and smaller minute and second pieces; decimal degrees combine all the pieces into one degree measurement.
- 1° = 60′ = 3600″
- 1′ = 60″
- fractional degree × 60 = minutes
- fractional minute × 60 = seconds
Exchange a large token for sixty small tokens and a small token for sixty tiny ones, keeping the total value.
8°30′ = 8.5°
1° = 60′
1′ = 60″
D, M, S count degrees, minutes, seconds
The same idea, other ways
Each larger-unit box can be exchanged for sixty smaller-unit pieces. To subtract from an empty seconds column, exchange a minute for sixty seconds. If there are no minutes, exchange a degree for sixty minutes first. The packaging changes while the angle stays the same.
1° = 60′
1′ = 60″
90° = 89°60′0″
= 89°59′60″
Decimal degrees measure every piece in degrees. One minute is of a degree, and one second is . To reverse the process, keep the whole degrees and exchange only their leftover fraction into minutes, then exchange only the leftover fractional minute into seconds.
= 8.5°
Read an angle unit in the top row and its exchange below. The column under Minute, ′ says one minute equals 60 seconds. The degree column gives the next exchange, one degree equals 60 minutes.
| Angle unit | Meaning | Exchange |
|---|---|---|
| Degree, ° | One of 360 pieces in a revolution | 1° = 60′ |
| Minute, ′ | One of 60 pieces in a degree | 1′ = 60″ |
| Second, ″ | One of 3600 pieces in a degree | 3600″ = 1° |
Part 1: DMS notation and borrowing
Think of each column as a box containing pieces of one size. You cannot remove seconds from an empty seconds box. Exchange one minute for 60 seconds first. If the minutes box is empty too, exchange one degree for 60 minutes before exchanging a minute.
- DMS stands for degrees, minutes, seconds.
- Borrowing changes the packaging, not the total angle.
- 180° = 179°59′60″ uses the same two exchanges as 90°.
180° = 179°60′0″
= 179°59′60″
A borrowed minute contributes 60″
Reminder
Reminder: Complement and supplement totals
- Complement and supplement totals. A complement is subtracted from 90°; a supplement is subtracted from 180°.
Worked example
Borrow minutes without seconds
You are finding the positive opening still needed to complete 180°. Find the supplement of 112°40′.
Show the steps and the answer
180° = 179°60′
= 67°20′
- Rewrite as .One degree supplies 60 minutes, allowing subtraction of 40′ from a previously empty minute column.
- Minutes: . Degrees: .Subtract corresponding sizes after the exchange.
Counterexamples
What it is not, and the tempting wrong moves.
Tips and tricks
- Every borrowed piece must leave the larger column before it enters the smaller one.
Part 2: DMS to decimal degrees
To combine different-size pieces into one number, express everything in the same unit. A minute is a sixtieth of a degree, and a second is a 3600th. Add those degree fractions to the whole degrees. The decimal point then describes a part of one degree.
- Use D + + .
- 1′ ≈ 0.016667°, rounded to six decimal places.
- 1″ ≈ 0.00027778°, rounded to eight decimal places.
- Use the exact fractions until the final rounding.
Reminder
Reminder: Common denominator
- Common denominator. = , so + = .
Counterexamples
What it is not, and the tempting wrong moves.
Tips and tricks
- Write the two exact fractions before touching the calculator. Round after adding all three pieces.
Part 3: Decimal degrees to DMS
Keep the whole large pieces and convert only the leftover part to smaller pieces. This is like exchanging the fraction of a large token that remains after setting aside all the whole ones. After minutes, do it again with the remaining fraction of a minute.
- Whole-number part gives whole degrees.
- Fractional degree × 60 gives minutes.
- Fractional minute × 60 gives seconds.
- Round seconds last and carry if the rounded value is 60.
21.256° = 21° + 0.256°
0.256 × 60 = 15.36′
0.36 × 60 = 21.6″
Nearest second: 21°15′22″
Reminder
Reminder: Rounding and carrying
- Rounding and carrying. If seconds round to 60″, exchange them for 1′. If that creates 60′, exchange those for 1°.
Counterexamples
What it is not, and the tempting wrong moves.
Tips and tricks
- At each stage set aside the whole pieces. Multiply only the leftover fraction by 60.
5 How
- For DMS subtraction, align the degree, minute and second columns. If needed, borrow one degree as 60 minutes, then one minute as 60 seconds.
- Subtract each column after the units are available. Check by adding your answer to the original angle.
- For DMS to decimal degrees, keep the degrees and add minutes ÷ 60 and seconds ÷ 3600.
- For decimal degrees to DMS, keep the whole degrees. Multiply only the leftover decimal by 60; keep its whole minutes.
- Multiply the new leftover decimal minute by 60 for seconds. Round at the end; if seconds round to 60, carry one minute. If minutes reach 60, carry one degree.
- In the table picture, read a column under Degree, °, then compare the matching information below it. Each column preserves one complete row of the reference table.
Choose subtraction or the correct conversion direction
- Read the requested operation and label the units in each column.
- For DMS subtraction, exchange larger pieces until each smaller column has enough, then subtract matching columns.
- For DMS to decimal degrees, use D + + before the final rounding.
- For decimal degrees to DMS, keep the whole degrees, multiply the leftover by 60, keep the whole minutes, and multiply their leftover by 60.
- Round seconds as requested and carry complete groups of sixty.
- Check subtraction by addition, or check conversion by converting the unrounded value back.
6 Worked example
Worked example
A triangle's third angle in degrees, minutes and seconds
A triangular plot of land has corners P, Q and R. A surveyor measures the angle at Q as ∠Q = 48°37′25″. A mapping program lists the angle at P in decimal degrees as ∠P = 63.4333°. (a) Write ∠P in degrees, minutes and seconds, rounded to the nearest second. (b) The three angles of a triangle add to 180°. Using your answer to (a), find ∠R in degrees, minutes and seconds. (c) Write ∠R in decimal degrees, rounded to four decimal places.
Show the steps and the answer
- (a) Split into whole degrees and a leftover. Keep . The leftover is 0.4333 of a degree.The whole-number part is already in degrees. Only the decimal part needs to be changed into minutes and seconds.
- Multiply only the leftover by 60: . Keep the whole minutes, , and set aside the leftover .1° = 60′, so a fraction of a degree times 60 gives minutes. Do not round 25.998′ to 26′ yet, because its decimal part still holds the seconds.
- Multiply the leftover minute by 60: . Now round to the nearest second: .1′ = 60″. Rounding happens only at the end, on the seconds.
- Since , carry one minute, so becomes . The minutes, 26, are less than 60, so no degree is carried. This gives .A finished DMS angle never shows 60 seconds or 60 minutes. A full 60 is traded for one of the next larger unit, so writing 63°25′60″ would be a mistake.
- (b) Write , and rewrite as .180° has 0′ and 0″, so those columns have nothing to subtract from. Borrowing 1° as 60′, then 1′ as 60″, gives the same angle with enough in every column.
- Align the columns and subtract from . Seconds: . Minutes: . Degrees: . This leaves .Degrees sit under degrees, minutes under minutes and seconds under seconds. Every top entry is at least as large as the one below it, so each column subtracts on its own.
- Align under . Seconds: . In the minutes column, is less than , so borrow one degree as 60 minutes: .1° = 60′, so moving one degree into the minutes column changes how the angle is written but not its size. It makes the minutes column large enough to subtract.
- Finish the subtraction. Minutes: . Degrees: . So .Once every column has enough units, each column is subtracted separately. The seconds column already gave 35″.
- (c) Keep the 67 degrees and add minutes ÷ 60 and seconds ÷ 3600: … … …One minute is of a degree and one second is of a degree.
- Round to four decimal places: 67.943055… .The digit after the fourth decimal place is 5, so the fourth decimal place rounds up from 0 to 1.
- (a) ∠P ≈ 63°26′0″
- (b) ∠R = 67°56′35″
- (c) ∠R ≈ 67.9431°
Work to write
- 0.4333 × 60 = 25.998′ → 25′
- 0.998 × 60 = 59.88″ ≈ 60″ = 1′
- ∠P ≈ 63°26′0″
- 180° = 179°59′60″
- 131°22′35″ = 130°82′35″
- ∠R = 67°56′35″
- ∠R ≈ 67.9431°
- Check: 48°37′25″ + 63°26′0″ + 67°56′35″ = 178°119′60″ = 180°
Ladder: from easy to exam-hard
Try each rung before you open its steps.
Rung 1 of 8
One smaller-unit fraction
You are expressing angle minutes as parts of one degree. Write 30′ as decimal degrees.
Show the steps and the answer
- .60 minutes fill one degree, so 30 fill half of it.
Rung 2 of 8
Subtraction without exchanges
You are finding the turn size left after removing the smaller DMS angle. Subtract 18°10′20″ from 42°30′50″.
Show the steps and the answer
Seconds: 50 − 20 = 30
Minutes: 30 − 10 = 20
Degrees: 42 − 18 = 24
- .Both amounts count seconds and the first is large enough.
- .No borrowing was required, so the minute column is unchanged.
- .Subtract the whole-degree column independently.
Rung 3 of 8
Borrow a degree for minutes
You are finding the positive opening still needed to complete 180°. Find the supplement of 112°40′.
Show the steps and the answer
180° = 179°60′
= 67°20′
- .Exchange one degree for 60 minutes so you can subtract 40′.
- .179 − 112 = 67 and 60 − 40 = 20, with the same units in each column.
Rung 4 of 8
Borrowing twice to subtract from 90°: tilting a telescope straight up
A telescope starts level, pointing at the horizon. The display on its mount shows that it has now been tilted upward through 34°19′52″. Pointing straight up, at the point directly overhead, takes a tilt of exactly 90° from level. Through what further angle must the telescope be tilted upward to point straight up? Give the angle in degrees, minutes and seconds, show each exchange you make, and check your answer by addition.
Show the steps and the answer
- Set up the subtraction . Write as so the columns line up: over over over .Straight up is 90° from level, so the tilt still needed is 90° minus the tilt already made. Only like units can be subtracted. Writing 00′ and 00″ shows that the top minutes and seconds columns are empty.
- The seconds column needs 00″ − 52″, which cannot be done. The minutes column has no minute to lend. So first borrow one degree as 60 minutes: .1° = 60′, so trading one degree for 60 minutes leaves the angle the same size. The seconds can only borrow from the minutes column, so that column must hold some minutes before it can lend one.
- Now borrow one of those minutes as 60 seconds: .1′ = 60″, so the angle is still unchanged. Together the two exchanges give the rule 90° = 89°59′60″. Now every top entry is at least the entry below it: 89 ≥ 34, 59 ≥ 19 and 60 ≥ 52.
- Subtract column by column. Seconds: . Minutes: . Degrees: .After the exchanges each column holds enough of its own unit. Each column can therefore be subtracted on its own with no further borrowing.
- Combine the three column results: .The minutes (40) and the seconds (8) are each less than 60. Nothing needs to be carried, so the angle is already in standard degrees-minutes-seconds form.
Work to write
- 90°00′00″ = 89°60′00″ = 89°59′60″
- Further tilt = 55°40′08″
- Check: 55°40′08″ + 34°19′52″ = 89°59′60″ = 90°
Rung 5 of 8
Both missing partners: the turns from a ship's course to due east and to due south
A ship's navigator sets a straight course turned 27°48′35″ clockwise from due north, so the ship heads between north and east. Measured clockwise from due north, due east is a quarter turn of 90° and due south is a half turn of 180°. (a) Find the complement of the course angle: the further clockwise turn that would swing the ship from its course to due east. (b) Find the supplement of the course angle: the further clockwise turn that would swing the ship from its course to due south. Give both answers in degrees, minutes and seconds, and check each one by adding it to 27°48′35″.
Show the steps and the answer
- Write each missing partner as a subtraction. Turn to due east (the complement). Turn to due south (the supplement).Turning clockwise from north, the course angle and the further turn together make the whole turn to the target. That is a quarter turn of 90° to reach east and a half turn of 180° to reach south. So each missing partner is the whole turn minus the part already turned.
- Line up the columns for the complement, over . Borrow as to get . Then borrow of those as to get .The top angle has 0′ and 0″, so 48′ and 35″ cannot be taken away. Since 1° = 60′ and 1′ = 60″, the exchanges change only how 90° is written, not its size: 89°59′60″ = 89°60′ = 90°. The exchanges are in sixties, not in tens as in ordinary subtraction.
- Subtract each column. Seconds: . Minutes: . Degrees: . The complement is .After the double borrow, each top entry is at least as large as the entry beneath it (60 ≥ 35, 59 ≥ 48, 89 ≥ 27). So each column subtracts on its own with no further exchanges.
- Line up the columns for the supplement, over . Rewrite as : borrow as to get , then borrow as .The half turn also has 0′ and 0″, so it needs the same double borrow. 179°59′60″ still equals 180°.
- Subtract each column. Seconds: . Minutes: . Degrees: . The supplement is .The seconds and minutes columns hold the same numbers as in the complement, so they give the same 11′25″. Only the degree column changes, because the top now has 179° instead of 89°.
- Compare the two partners: .Since 180° − θ = (90° − θ) + 90°, the supplement must be exactly 90° more than the complement, with the same minutes and seconds. The matching 11′25″ in both answers shows the smaller columns were handled the same way in both subtractions.
Work to write
- Complement (turn to due east) = 90° − 27°48′35″
- 90° = 89°59′60″
- Supplement (turn to due south) = 180° − 27°48′35″
- 180° = 179°59′60″
- Check: 62°11′25″ + 27°48′35″ = 90°0′0″ and 152°11′25″ + 27°48′35″ = 180°0′0″
Rung 6 of 8
Both smaller units into one decimal: a bracket angle for a laser cutter
A metal shop is remaking a steel bracket from an old drawing. The drawing marks the angle between the bracket's two arms as 71°14′51″. The shop's laser cutter accepts angles only in decimal degrees, with up to four decimal places. Use 1° = 60′ and 1′ = 60″, so 1° = 3600″. (a) Write 71°14′51″ in decimal degrees. This is the number to type into the cutter. (b) A coworker suggests copying the digits and typing 71.1451. Would the cutter's angle then be too large or too small, and by how many degrees?
Show the steps and the answer
- Split the angle into its columns: . Keep the 71 whole degrees as they are.The degrees are already in the unit the cutter wants. Only the 14 minutes and 51 seconds are smaller pieces of a degree that still need converting.
- Turn the minutes into degrees: degrees .1° = 60′, so one minute is of a degree. A minute is a sixtieth of a degree, not a hundredth, so the digits 14 cannot just be placed after the decimal point.
- Turn the seconds into degrees: degrees .1° = 60′ = 60 × 60″ = 3600″, so one second is of a degree. Dividing by only 60 would turn the seconds into minutes, not into degrees.
- Put the minutes over 3600 and add: , so .Fractions can be added only over a common denominator, and 3600 = 60 × 60 is a multiple of 60. Exact fractions also avoid rounding 14 ÷ 60 = 0.2333… too early. Any rounding waits until the end.
- Divide: . On a calculator, .Dividing top and bottom by 9 gives . Multiplying top and bottom by 25 turns it into ten-thousandths. So 14′51″ is exactly 0.2475 of a degree, with four decimal places and nothing to round.
- Add back the whole degrees: .Decimal degrees = D + + , here with D = 71, M = 14 and S = 51.
- (b) Compare the copied entry with the true value: .71.1451 is the smaller number, so the cutter would make the angle 0.1024° too small. Copying the digits treats 14′51″ as of a degree, but it is really = of a degree. The error is more than 6 minutes, since 0.1024 × 60 = 6.144′.
Work to write
- 71°14′51″ = 71.2475°
- (b) 71.2475 − 71.1451 = 0.1024, so 71.1451 is 0.1024° too small
Rung 7 of 8
One decimal back into minutes and seconds: a waterfall's latitude for a trail guide
A hiking club is printing a trail guide that lists the latitude of each landmark in degrees, minutes and seconds, rounded to the nearest second. (Latitude is an angle. It measures how far north or south of the equator a place lies.) A member's phone app gives the latitude of a waterfall on the club's Blue Loop trail as 39.4147° N, in decimal degrees. Using 1° = 60′ and 1′ = 60″, write the waterfall's latitude in degrees, minutes and seconds, to the nearest second, for the guide.
Show the steps and the answer
- Split off the whole degrees: . The goes straight into the answer.The digits before the decimal point already count complete degrees. Only the leftover 0.4147° is less than one degree, so only that part needs to be rewritten in the smaller units.
- Turn the leftover degree into minutes: .1° = 60′, so any part of a degree is worth 60 times as many minutes. Multiply only the leftover 0.4147, not 39.4147. The digits 4147 are ten-thousandths of a degree, not minutes and seconds. Reading them as 39°41′47″ would give about 39.6964°, which is a different latitude.
- Keep the whole minutes, , and carry the leftover to the next step.24.882′ is 24 complete minutes and most of another minute. Rounding up to 25′ here would throw the leftover away. The 0.882′ is still part of the angle, and it becomes the seconds.
- Turn the leftover minute into seconds: .1′ = 60″, so a part of a minute times 60 gives the same amount in seconds.
- Round at the end: to the nearest second. Since 53 is less than 60, nothing carries into the minutes column.Seconds are the last unit, so this is the only place to round. Rounding earlier changes the answer. For example, rounding 24.882′ to 24.9′ first would give 0.9 × 60 = 54″, which is one second too many.
- Put the columns together: , keeping the N from the app.Each column now holds a whole number below its limit (24 < 60 and 53 < 60), so no column needs adjusting. The N still shows that the waterfall is north of the equator.
Work to write
- 39.4147° = 39° + 0.4147°
- 0.4147 × 60 = 24.882′ → keep 24′, leftover 0.882′
- 0.882 × 60 = 52.92″ ≈ 53″
- 39.4147° N ≈ 39°24′53″ N
Rung 8 of 8
Rounding spills into the next column
You are describing the same turn with a different measuring unit. Convert 12.9999° to DMS to the nearest second.
Show the steps and the answer
12°59′59.64″
≈ 12°59′60″
= 12°60′0″
= 13°0′0″
- Keep . Compute .Only the fractional degree changes into minutes.
- Keep . Compute .Only the fractional minute changes into seconds.
- rounds to . Exchange for , giving .Nearest-second rounding goes upward, and 60 seconds make one minute.
- Exchange for , giving .Standard DMS form uses fewer than 60 minutes and fewer than 60 seconds.
Counterexamples
What it is not, and the tempting wrong moves.
Tips and tricks
- Write the symbols beside each column so you subtract matching units.
- Convert or round only the leftover fractional part. Whole degrees remain degrees and whole minutes remain minutes.
- Round at the final step, then carry a full group of sixty into the next larger unit.
7 The trap
Treating DMS as decimal digits. 6′ is ° = 0.1°, not 0.06°. Borrow and carry in groups of 60, not 100.
Keep in mind
- Borrow and carry in groups of 60, never 10 or 100: trading 1° gives 60′, not 100′.
- Subtract seconds, then minutes, then degrees, and borrow only when a column runs short: 44°40′30″ − 21°10′15″ = 23°30′15″ needs no borrowing.
- To change DMS to decimal degrees, divide minutes by 60 and seconds by 3600: 10°30′ = 10° + ° = 10.5°.
- A minute is a sixtieth of a degree, so 6′ = ° = 0.1°, not 0.06°.
Memory hook
Degrees split like hours on a clock: 60 minutes in a degree, 60 seconds in a minute. Borrow 60, never 100: 90° = 89°59′60″.
Flash cards
Say the answer out loud, then flip.
What is one minute (1′) of angle?
How many seconds (″) are in 1°?
What are the two ready-made borrows?
- 90° = 89°59′60″
- 180° = 179°59′60″